What To Do After Replacing Camshaft Sensor? (Explained)

Your camshaft going haywire is the quickest method to render your engine powerless. In a petrol or diesel engine, a camshaft sensor is an electrical device that monitors the location or rotational speed of the camshaft.

When a camshaft sensor fails, it transmits erroneous information to the engine, such as uneven fuel delivery, incorrect ignition timing, and so on.

The camshaft position sensor must be replaced if any sensors fail, causing the engine to run rough or causing difficulty starting the car.

What to do after replacing camshaft sensor? After replacing the camshaft sensor, you’ll need to use a diagnostic scanner to clear the problem code. The code is kept in the engine controller, so keep that in mind. In addition, if the camshaft position scanner fails, it cannot be repaired or reused.

That’s just a quick fix that doesn’t go into great detail. Later in this article, we will offer you information on those. Hopefully, you’ll be able to solve the camshaft position sensor issue in a timely manner.

What To Do After Replacing Camshaft Sensor?

As previously stated, after replacing the camshaft sensor, you must use a diagnostic scanner to clear the error code. The code is kept in the engine controller, so keep that in mind. In addition, if the camshaft position scanner fails, it cannot be repaired or reused. Let’s go to the details.

Check A Cam Sensor

The magnetic type sensor is the one we go with. The voltage is produced by this type of sensor, which has two wires.

You don’t have to take the sensor from the automobile to test it; instead, you may do it right from your car.

To begin, inspect the plastic housing of your sensor for any large cracks or damage, as well as whether it is bent out of shape. You have a defective sensor if you see such signs.

Get your multimeter out and perform a resistance test. The multimeter must then be set to the ohms setting. In terms of resistance, our camshaft position sensor measures between 2000 and 2500 ohms.

On the scale of this multimeter, choose 20,000 ohms, and then we’ll take our measurement. We now have a resistance of 2.01 thousand ohms or 2010 ohms. You should also inspect the condition of your sensor’s connector.

Sensor Reprogramming Or Not

The first thing to remember after replacing your old problematic camshaft position sensor with a new one is that you must reprogram the sensor if it requires it, and the second thing is to use an OBD-2 diagnostic scanner to delete the error codes recorded in the car’s engine controller.

The ECM relearns the pulse timing in most circumstances, so you don’t have to reprogram the sensor. However, the ECM may require reprogramming, which is performed through the OBD-2 diagnostic scanner in some situations.

When a replacement camshaft sensor is placed in some autos, the error code disappears on its own, leading you to believe the issue has been cleared. However, there’s a good probability the code will reappear. So, after replacing the camshaft sensor, the best thing to do is manually clear the problem with an OBD-2 diagnostic scanner. This confirms that the sensor is properly installed.

If the replacement camshaft sensor is inserted and the code reappears after manually clearing it with the OBD-2 Scanner tool, the next step is to inspect the electrical connector and make sure it is pushed correctly to hear a click.

Because there’s a good chance the connector isn’t in the right place. If the car still gives you an error message after you’ve checked the connector, you can try installing a new camshaft sensor; new sensors might occasionally be too defective.

How Much Does A Camshaft Position Sensor Replacement Cost?

For those of you who haven’t updated your sensors yet but are reading this page for information, a camshaft sensor replacement can cost anywhere from $120 to $300.

Depending on your car, other elements such as gaskets and the valve cover may need to be removed to have access to the sensor. In that situation, you might need to add $20-$40 to your budget.

If you need new parts, they can cost anything from $50 to $200. In terms of labor costs, they might range from $70 to $100, depending on the skilled mechanic and his service rates.

These are, however, average expenses, and the cost of installing the sensors and their parts will vary depending on the type and brand of the car you possess.

If you have a luxury vehicle or want a local car dealership to replace it for you, the fees will be higher. Naturally, charges will vary based on where you want your sensor repaired.

What Is The Average Time To Replace A Camshaft Sensor?

Surprisingly, removing and replacing your vehicle’s camshaft sensor is simple. It also doesn’t take long to replace a camshaft sensor. In most cases, the replacement will take between 5 and 10 minutes.

You should be aware of a few key considerations before replacing them. You must detach the positive battery cable whenever you operate with electrical components or sensors. After removing the pigtail, inspect it for any damage or dirt. Keep in mind that corrosion and oil can interfere with the sensor’s signal to the engine control module.

You should also inspect the sensor carefully to verify that it does not leak any other engine components. If you see any damage, you must patch the leak to avoid damaging the replacement sensor. Additionally, check to see if the sensor’s o-ring has dropped into its hole.

Replacing the sensor is as simple as pushing it into place, replacing the bolt and electrical hookup, and tightening the bolt according to the manufacturer’s instructions. However, be careful not to overtighten the bolt, since this could damage the new sensor’s mounting ear.

Finally, after replacing the camshaft position sensor, make that the engine light is still on.

Benefits of a Quality Camshaft Sensor

As a vehicle owner, you need a good camshaft sensor for a variety of reasons. Aside from getting rid of stress, there are a number of other intriguing issues to consider. They are as follows:

1. Significant Fuel Consumption

Aside from a relaxing ride, every car owner enjoys being able to spend the amount of money they choose on gas and not being compelled to pay more due to the engine’s excessive consumption of fuel.

Overconsumption of fuel isn’t a pleasant feeling, especially if the driver doesn’t have a lot of resources; they limit their movements merely to keep the tank full.

A decent camshaft can relieve the tension of spending too much money on petrol.

2. Pleasurable Driving Experience

A faulty engine will make driving unpleasant. Nothing is more humiliating than having a client in your car when it breaks down. When your engine stops working properly, it can be excruciating.

Every driver does not want to be chastised for mishandling engines. For this reason, it has been observed that drivers pay greater attention to their car engines than to other automotive components.

Your engine’s efficiency is great when it has a decent camshaft. A decent car is a magnificent car, not only because of its beauty but also because you may drive it in peace.

3. Make Quick Use of the Gear

Another intriguing feature that any fast driver will appreciate is the option to maximize the power of their gears.

It’s difficult to alter gears to taste when there’s a camshaft problem. It wouldn’t be fun to be on the highway and have your gear seize because you decided to slow down or add a little nitro.

4. The Danger Engine Light Isn’t Flashing

Another approach to appreciating life is to take a tranquil ride. When drivers see flashes signifying danger from the car’s engine, they become panicked.

Even if the driver has high hopes and is tenacious, the sight of sparks and lights indicating that the engine is plagued with a problem causes panic and a desire to investigate what is wrong.

A good camshaft cannot be overstated in terms of the peace it brings to the car and the car owner.

Final Thoughts

It’s exhilarating to know what to do if your car breaks down. It’s not difficult to fix your camshaft, and resetting it isn’t difficult either. As a result, know what to do if your car’s camshaft sensor has to be replaced. I hope you are able to find the most appropriate response to your query. So, if you have any requests, please post them in the comments section below.

Leave a Comment