Does your viper remote start not working after disconnecting battery? These are questions to ask if your car’s remote control isn’t working. Smart keys, which can control operations like starting the car, opening and closing the door, and so on, are commonly used in today’s cars.
However, when you’re distracted, it’s this convenience and modernity that can cause a lot of problems. Here are some of the most prevalent remote starting scenarios.
If the viper remote isn’t working, This means that the vehicle’s owner or driver cannot operate it remotely. This diminishes convenience while also limiting a vehicle’s safety features. When the remote control stops working, you will be quite uncomfortable.
So you need to figure out why your remote control isn’t working after the battery has been replaced. What should you do if your remote control is broken? Please take the time to read this article.
Why Viper remote start not working after disconnecting battery?
There are many reasons why your viper remote does not work after replacing the battery. Maybe you made a mistake in the process of replacing the battery for the remote starter; after changing the battery you don’t program etc. Find out more details through the reasons below.
1. Made a mistake during the battery replacement?
One of the reasons why your remote starter cannot be used is because you did the wrong battery replacement process. Maybe you touched some part of the circuit. Please check the steps below to replace the battery to see if you are doing it correctly.
Step 1: Check the back of your remote for screws. Look for a notch on the side where the two halves of the remote meet if there are no screws.
Step 2:
Remove the screws by loosening them. Alternatively, pry the remote open with a penny.
Step 3:
Get rid of the old battery. Do not touch any of the internal circuitry or the battery terminal.
Step 4: Replace the battery. On one side of the battery, there is a positive symbol. This site is normally on the bottom. Check your manufacturer’s directions to be sure you didn’t put the battery in the wrong way.
Reassemble the two sections by snapping them together. Replace any screws that you have to remove.
If none of the previous processes have shown any unexpected indicators, please join us for the next section.
2. Have not reprogrammed the remote starter yet?
Although the battery was properly replaced, the viper remote is still not working, possibly because it has not been reprogrammed. It isn’t necessary to reprogramme the remote all of the time, but if it doesn’t work after replacing the batteries, you should.
Here is how to reprogram the remote starter you can refer to.
For one second, press and hold the “Lock” button on your fob remote car starter. Turn your key to the “Off” position to turn off the automobile lights. Do this within five seconds of turning the key to the “On” position, and don’t remove the key until the “Off” position is reached.
If your car key remote is not pairing, you should replace it. Most remote controls can only be configured once, and reprogramming them may be impossible.
3. Have not you turned off the hazard lights?
If remote start does not function, check your vehicle’s danger warning lights first. When you approach a hazard or an emergency situation, this light flashes, preventing your car from starting automatically.
If the symptom persists, switch off the warning lights and try again with the remote start. If this does not solve the problem, try modifying the gauge settings.
If your car’s danger lights continue to flash, the issue could be with the remote start. Some versions have a feature that prohibits the car from starting without the use of a key.
Resetting the feature is doable, but it will necessitate a trip to your dealer. This technique, though, should be rapid, allowing you to get back behind the wheel soon. The remote start and danger warning lights can also be manually reset.
Turn off the battery and reset the car’s electronics to check the remote start and hazard warning lights. Factory remote start systems do not connect to the hazard warning lights, which is vital to remember.
They merely turn on the parking lights instead. This isn’t the most ideal situation. The best solution is to change the system’s configuration to include side signals.
4. Have not turned off engine lights
There are a few things you can do if your remote start isn’t working while your car’s check engine light is illuminated. If the issue is caused by low oil pressure or coolant temperature, open the hood to let the car cool down. You may not have enough oil in the system in some circumstances.
If that doesn’t work, you may always contact a mechanic for a free repair. You may also simply take your car to an auto shop and get it tested for free.
A problem with the gas cap is another possible cause for the remote to stop working. Make certain the cap is securely fastened. The check engine light will go away if you turn it off for a bit, but it may not work at all. You should try to replace the gas cap in either situation. Although the issue may be more serious, a new gas cap should assist.
5. Hood open
Another reason the remote start isn’t working is that the hood is open. To use the remote start system, the hood must be closed. With your hands, close the hood securely. You may have a cracked or corroded pin if it doesn’t latch properly. You won’t be able to transmit a signal to the remote starter if this happens.
If the issue persists, you could inspect the hood latch switch. If the hood pin is loose, the remote start may not operate, so make sure it is properly closed. In the dash menu, check the gauges for the hood latch.
Lock the doors and hold the button for at least 2 seconds before attempting to utilize your remote start. After that, try the remote start once more.
6. Examine Your Indicators
Check to see whether your oil pressure or coolant temperature are both too low. The remote start will not work if your display readouts reveal these types of anomalies. As you may have noticed, the remote start has numerous precautions in place to prevent engine damage, and this is just another example of that trend.
Before attempting another remote start, make sure your car has cooled down. If it’s clear that these gauges are indicating these issues incorrectly, you’ll need to solve them before the remote start can work.
Consult a locksmith if everything else fails. A locksmith can assist you in resolving the remote start issue and replacing the key. The work will be done correctly if you hire a locksmith. Furthermore, because the locksmith may come to you, you will save money. You can call a mobile locksmith if you don’t have time to visit a service establishment.
Frequent Asked Questions
Q: Is it possible to configure a fresh key fob yourself?
In some circumstances, you may be able to program your own key fob. Each automobile will have its own programming method. This will not function if the remote is not blank and has been previously programmed to another vehicle.
Q: What is the cost of reprogramming a key fob?
Depending on the automaker and the complexity of the design, upgrading an electronic key fob can cost anywhere from $50 to over $100. Every key fob must be programmed. Some vendors would do it for free, while others may charge between a half-hour and an hour of labor.
Q: What happens if the battery in your car key dies?
There is still a way to start the automobile if your keyless entry system uses a START button and there is no mechanical keyhole. Push the START button with the key fob. If the key fob battery dies, certain manufacturers feature a backup system that permits this way to work.
Q: How Do You Reset Your Viper Remote Start?
A Viper remote start can be reset in several ways. One option is to employ a keyless entry system. You must first unlock the driver’s door with the key before opening the hood with the keyless entry technique. Locate the black box near the right headlight once you’ve opened the hood. The black box has a small opening on one side. Insert a paper clip into the hole and press down for five seconds on the button within. Release the button after five seconds and remove the paper clip. Now is the time to reset the remote start.
Q: A Viper remote uses what kind of battery?
This sleek silver remote is ideally designed to function flawlessly with your car and will complement any interior. You’ll always have it on hand because it’s compact and fits well in a purse or pocket.
The Viper Remote is a long-lasting device that runs on CR2016 or CR2032 batteries. These tiny batteries will last around a year and should be replaced once a year to keep the remote safe to use.
Q: What exactly is the Viper valet mode?
What is Valet Mode, exactly? At some time, we all have to hand over control of our vehicle to someone else. Whether it’s a restaurant valet or a mechanic at your neighborhood garage. With valet mode, you may disarm your alarm and hand over the keys without having to worry about your security system.
Final thoughts
We offered advice on how to repair a remote starter that had stopped working after the battery had been replaced. This is a regular occurrence that is also simple to solve. However, in some cases where the control is significantly damaged, I recommend consulting a specialist for assistance. If you don’t know how to fix it, don’t bother. It will either be very expensive or you will have to replace it. I hope you enjoyed the article. If you have any further questions, please contact us.