The Engine Warning Light (Check Engine Light)is an important component of your vehicle’s on-board diagnostics OBD system.
The diagnostic system both controls and monitors the performance of your vehicle. This system regulates things like gasoline mix, engine speed, and gearbox functions.
The Engine Warning Light illuminates when a built-in computer detects an issue that it cannot automatically resolve.
The Engine Warning Light might indicate an engine check, a powertrain check, or an early maintenance engine.
After the Engine Warning Light indicated a problem and you resolved it. They do not, however, turn off or reset themselves. As a result, you must restart. In this article, we will talk about Ford C-max Engine Warning Light reset.
Why Is Your Ford C-max Engine Warning Light On?
Your Engine Warning Light came on due to a problem that you remedied, but it won’t go away now. You may not be to blame for this.
Your car’s computer may occasionally require a little assistance to confirm that the problem has been fixed. I’ll discuss a couple methods for turning off your Engine Warning Light.
When your vehicle’s onboard computer system detects an electrical or mechanical issue, this light will turn on.
The engine light sometimes stays on even after the issue has been resolved. This can be inconvenient, resulting in you failing an emissions test. Or maybe it prevents you from learning about any future issues that your car’s computer could be trying to warn you about.
Since your engine does still have an issue, it is imperative to make sure the light isn’t on. To turn the light out, try one of the following methods. If it doesn’t, there’s a problem with your engine.
Read more: Reasons That Remote Start Not Working And Check Engine Light On?
Guidelines For Ford C-max Engine Warning Light Reset
By using an OBD2 scanner, you may reset the Engine Warning Light in the simplest manner possible.
If not, try pulling a fuse, cycling the ignition, unplugging the battery, or just waiting for it to go away on its own.
The following instructions will show you how to reset your Ford C-max engine warning light in more detail:
Use An OBD2 Scanner
Your Engine Warning Light can be quickly reset if you have access to an OBD2 scanner.
Connect the scanner to the OBD connector found beneath the steering column of the majority of automobile models while your Engine Warning Light is on. Next, turn the ignition to the “ON” position in your car. Press the “read” button on the scanner to go through all of the stored fault codes after the computer and automobile have connected.
After the scan is finished, write down all error codes that the scanner identified, then utilize the user manual for that particular make and model to decipher those issues.
The issue is identified after the code has been deciphered. If that component needs to be changed, do so; likewise, if it needs to be calibrated, do so.
Once finished, click the “Erase/Clear” button to remove the error from the scanner. It is advised to turn off the ignition when the issue has been resolved.
Then you need to turn it back on to make sure the engine check light hasn’t come back on. Additionally, you should check the scanner again to see whether the same error is being reported.
Disconnecting Batteries Technique
Without a scan tool, disconnecting the battery terminal for 30 to 60 seconds is the most effective approach to turn off the Engine Warning Light.
Remove the automobile battery’s negative terminal. Then, try to exhaust any remaining electricity in the capacitor of the automobile by sounding the horn for 20 to 30 seconds or turning on the lights.
After the electricity has been turned off, park your automobile for 10 to 15 minutes. After a little while, reconnect the battery terminals, check that they are securely fastened to prevent any potential sparking. Then turn the Ford C-max on.
After restarting, if your car still displays the Engine Warning Light, there may be a significant issue with it or the automobile may have stored the codes.
Because some automobile models won’t allow the codes to be reset by cutting the power in this situation, it is strongly advised to check the codes with a scanner instead.
Turning the Ignition On and Off
Another way to perform a hard reset without disconnecting the batteries is to turn the ignition on and off repeatedly.
After inserting the keys, turn the ignition on and off one at a time, waiting a second between each.
Once it is finished, check to see if the engine check light is still on. You are prepared to go if the check light is out, but if it is still coming on, you should be ready by scanning the codes.
Remove The Fuse and Replace
The engine control unit’s fuse can be removed and then reinstalled as one method of turning off your Engine Warning Light.
Although this won’t fix the issue in newer automobiles, it might in somewhat older cars, and it’s simple to test. For help locating the fuse for the engine control unit, consult your repair manual.
Justifications For Not Ignoring The Engine Warning Light
Most people will simply ignore a warning light that illuminates on their dashboard. If there is a minor issue with their car that does not impair the engine’s performance and continue driving.
However, this is a terrible idea. Because it means you won’t be able to tell right away if there is a more major issue with your engine that is causing the check light to come on. Even if it is just a minor issue.
The sole indication of an issue like improper camshaft timing may be a check engine light on your dashboard. However it might eventually cause the entire engine to fail. Therefore, even if the issue is minor and simply resulted in the indicator light, you should always address it.
Frequently Asked Questions
Q: How much does checking the check engine light cost?
The majority of mechanics will bill you at an hourly labor rate only to connect an OBD-II diagnostic scanner and explain the problem. The responsibility to address whatever the issue may be follows. Knowing the issue before you see the repair could help you save hundreds of dollars. You should invest in your own OBD-II scanner because of this.
Q: How do you use the gas pedal to reset the check engine light?
The accelerator pedal cannot be used to reset the warning light in the majority of car models. The ignition can be turned on, the gas pedal completely depressed and held, the brake pedal pressed seven times. Then the ignition can be turned off. Some car models will have the codes reset by doing this, but most won’t.
Q: How do I turn off my check engine light?
With a scanner, which provides an instantaneous response, you may reset the check engine light the simplest method possible. If not, you will have a significant delay after fixing the issue, and it might reset itself. You can also try cutting the negative battery cable if your car is older.
Final Thoughts
With the knowledge you have gained from this post, we hope you can fix the issues with your Ford C-max and the Engine Warning Light.